#-----------------------------------------------------------
#
#           Type <CE22> EEPROM DATA EDITOR HELP FILE 
#                      Version 0.11
#
#         Copyright (c) 1998 by YAESU MUSEN Co., Ltd.
#
#-----------------------------------------------------------
# 
# Help File Format Information
# 
# Special characters at the beginning of each line determine
# the function of that line:
#       `#' = Comment line, ignored by program
#       `:' = Control line. the program looks for these
#             lines, and reads the following characters as a
#             help subject label. One special case is
#             ":page", which indicates a page break within a
#             help subject. 
# Maximum line length for help items is 61 chrs. Longer lines
# are truncated. Maximum number of lines/screen is 16
# (additional lines are automatically moved to the next
# screen).
# 
#-----------------------------------------------------------
#
:chedit_chno

      [Channel Number for Display on the Transceiver]

 Pressing the Space Bar, toggles the data for the entire
 channel between hidden and unhidden (except the first
 channel, which cannot be hidden).
 Hidden channels display "--" in place of field entries, and
 are not used for operation (although they are still stored
 in hidden form for possible recall later).


 Space Bar:  Hide/Unhide entire channel (line).

#
#
#
:chedit_rxf
   [Edit Rx/Simplex Frequency & Hide/Unhide Channel Data]

 Use 0 - 9 to enter the desired channel frequency, and press
 Enter. This frequency will be adjusted if it does not match
 the Channel Step parameter, and will also appear in the Tx
 Freq field. You do not need to enter all 8 digits: empty
 digits to the right are zero-filled. Pressing [.] (period)
 after several digits forces them to MHz. Press period first
 to change only kHz.

 Pressing only the Space Bar without entering a number
 toggles the data for the entire channel between hidden and
 unhidden (except the first channel, which cannot be hidden).
 Hidden channels display "--" in place of field entries, and
 are not used for operation (although they are still stored
 in hidden form for possible recall later).
#
#
#
:page
#

 NOTE! Any entries or changes to this field will also occur
       in the Tx Freq. field, so you may need to edit that
       field after making any changes here.


 Arrow Keys: Change field (before or after editing 
                Frequency).
 Space Bar:  Hide/Unhide entire channel (line).
 0 - 9:      Input a digit.
 [.]:        Set last three (or fewer) digits as MHz, or
                next digits as kHz (if pressed first).
 Backspace:  Erase digit to the left, or cancel entry.
 Enter Key:  Accept displayed frequency, with zero-fill.
 Esc Key:    Cancel and return to previous frequency.

#
#
#
:chedit_txf
  [Enter Transmit Frequency & Enable/Disable Transmission]

 Use keys 0 - 9 to enter the desired transmitting frequency,
 and press the Enter key to accept. If the frequency does not
 match the Channel Step parameter, it will be adjusted to the
 nearest valid step. You do not need to enter all 8 digits:
 empty digits to the right are zero-filled.
 Pressing [.] (period) after several digits forces them to
 MHz, while pressing [.] first allows entering only kHz.
 
 Pressing only the Space Bar without entering a number
 toggles the the data for the entire channel between hidden
 and unhidden(except the first channel, which cannot be 
 hidden). Hidden channels display "--" in place of field
 entries, and are not used for operation (although they are
 still stored in hidden form for possible recall later).
#
#
#
:page
#

 NOTE! The Tx Freq is automatically copied from the Rx Freq,
      so any changes here will be LOST if the Rx Freq is
      changed. Therefore, the Rx Freq should be set first,
      before editing the Tx Freq. 

 Arrow Keys: Change field (before or after Editing Freq.)
 Space Bar:  Hide/Unhide entire channel (line).
 0 - 9:      Input a digit.
 [.]:        Set last three (or fewer) digits to MHz, or
               next digits to kHz.
 Backspace:  Erase digit to the left, or cancel entry.
 Enter Key:  Accept displayed frequency, with zero-fill.
 Esc Key:    Cancel and return to previous frequency.
#
#
#
:chedit_cdec

 [Toggle Subaudible CTCSS Decoder, and set CTCSS frequency]

 Press the Space Bar to toggle the decoder on/off, or press
 Enter to display the Tone Select window, from which you may
 select a frequency with the Arrow Keys (pressing Enter again
 to accept, or Esc to cancel).

 If you know the CTCSS frequency you want, you can enter it
 directly with the 0 - 9 and [.] (period) keys. When the
 desired CTCSS frequency is displayed, press Enter to accept.
 If the frequency was invalid (not among the standard tones),
 the Tone Select Window will appear as described above, with
 the nearest valid frequency pre-selected.
#
:page
#

 Turning on CTCSS turns off DCS (both cannot be on).
 CTCSS cannot be selected for use if ARTS is enabled (DCS 
 only).


 Arrow Keys: Change field, or select in Tone Select window.
 Space Bar:  Toggle Decoder on/off (except during selection).
 0 - 9, [.]: Direct tone frequency entry.
 Backspace:  Delete digit to left during direct entry.
 Enter Key:  Display Tone Select Window, and accept entry/
               selection.
 Esc Key:    Cancel input or selection.
#
#
#
#
:chedit_ddec

          [Toggle DCS Decoder, and set DCS Code]

 Press the Space Bar to toggle the decoder on/off, or press
 Enter to display the Code Select window, from which you may
 select a DCS Code with the Arrow Keys (pressing Enter again
 to accept, or Esc to cancel).

 If you know the 3-digit DCS Code you want, you can enter it
 directly with the 0 - 9 keys. When the desired Code is
 displayed, press Enter to accept. If the Code was invalid
 (not among the standard Code numbers), the Code Select
 window will appear as described above, with the nearest
 valid Code pre-selected.
#
:page
#

 Turning on DCS turns off CTCSS (both cannot be on).
 DCS encode and decode are both required for ARTS operation.


 Arrow Keys: Change field, or select in Code Select window.
 Space Bar:  Toggle Decoder on/off (except during selection).
 0 - 7:      Direct Code number entry.
 Backspace:  Delete digit to left during direct entry.
 Enter Key:  Display Code Select Window, and accept entry/
               selection.
 Esc Key:    Cancel input or selection.
#
#
#
:chedit_cenc
   [Toggle Tone Squelch Encoder, and set CTCSS frequency]

 Press Space to toggle the Encoder on/off, or press Enter to
 display the Tone Select window (if not viewing it already),
 from which you may select a frequency with the Arrow Keys
 (pressing Enter again to accept, or Esc to cancel).

 If you know the CTCSS frequency you want, you can enter it
 directly with the 0 - 9 and [.] (period) keys (entering
 a number or [.] forces the Encoder on). When the display
 shows the desired CTCSS frequency, press Enter to accept.
 If the frequency was invalid (not among the standard tones)
 the Tone Select Window will appear as mentioned above.

 NOTE! if the channel is hidden when you make an entry, it
 will be unhidden. Edit the Rx Freq field to hide it again.
#
#
#
:page
#

 NOTE: Turning on the CTCSS Encoder automatically turns off
 the DCS encoder, if it was on.
 
 Arrow Keys: Change field, or select in Tone Select window.
 Space Bar:  Toggle Encoder on/off (except during selection).
 0 - 9, [.]: Direct tone frequency entry.
 Backspace:  Delete digit to left during direct entry.
 Enter Key:  Display Tone Select Window, and accept entry/
               selection.
 Esc Key:    Cancel input or selection.
#
#
#
:chedit_denc
       [Toggle DCS Encoder, and set DCS Encoder Code]

 Press Space to toggle the Encoder on/off, or press Enter to
 display the Code Select window (if not viewing it already),
 from which you may select a code with the Arrow Keys
 (pressing Enter again to accept, or Esc to cancel).

 If you know the DCS code you want, you can enter it directly
 with the 0 - 7 keys (entering a number forces the Encoder
 on). When the display shows the desired code, press Enter to
 accept. If the code was invalid (not among the standard
 codes) the Code Select Window will appear as mentioned
 above.

 NOTE! if the channel is hidden when you make an entry, it
 will be unhidden. Edit the Rx Freq field to hide it again.
#
#
#
:page
#

 NOTE: Turning on the DCS Encoder automatically turns off
 the CTCSS encoder, if it was on.
 
 Arrow Keys: Change field, or select in Code Select window.
 Space Bar:  Toggle Encoder on/off (except during selection).
 0 - 7:      Direct code number entry.
 Backspace:  Delete digit to left during direct entry.
 Enter Key:  Display Code Select Window, and accept entry/
                selection.
 Esc Key:    Cancel input or selection.
#
#
#
:chedit_wide

                   [Wide/Narrow toggle]

 Press the Space Bar to toggle the FM mode Wide or Narrow.
 Wide = 25 kHz channel spacing, 5 kHz deviation.
 Narrow = 12.5 kHz channel spacing, 2.5 kHz deviation.
 
 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle wide/narrow.
 
#
#
#@
:chedit_clksft

                     [CPU Clock Shift]

 The software automatically assigns clock shift status as 
 needed for the programmed frequency.
 If a noticeable buzz is heard on the signal, changing the 
 status of the TX clock shift will ususally cure it.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle on/off.

#
#
#@
:chedit_nsqlv

                   [Noise Squelch Level]

 Press the Space Bar to toggle the Noise Squelch mode
 Intenal or Fixed.
 
 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle Prpgm(Pre Program)/User.


#
#
#@
:chedit_nsqfxlv

                     [NSQ Fixed Level]

 Press the Space Bar to toggle the Noise Squelch Level
 when Noise Squelch mode is "Fixed".
 
 Arrow Keys: Change fields after selection.
 Space Bar/Backspace: Increment/Decrement NSQ Fixed Level.


#
#
#
:chedit_cblip

                      [Courtesy Blip]

 When ON, the VXR-7000 sends out a beep on the portable
 radio frequency each time the portable radio is unkeyed.
 This beep is not tranmsitted by the connected mobile radio. 
 
 Arrow Keys: Change fields after setting on/off.
 Space Bar:  Toggle on/off.
#
#
#@
:chedit_revbst

                      [Reverse Burst]


 Press the Space Bar to toggle the Reverse Burst on/off.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle on/off.

#
#
#
:chedit_dcstype

                       [DCS Type]

 Effective only when DCS is chosen as the coded squelch.
 A = Normal DCS
 B = Inverted (complement) DCS

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle A/B.
#
#
#
:chedit_ddectype

                      [DCS Dec Type]
  
 Selects ability to decode the DCS complement.
 Fixed = Decodes the selected type only (normal ORinverted)
 Auto  = Decodes both types (normal AND inverted)

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle Auto/Fixed.
#
#
#@
:chedit_mlttone

                   [Multi Tone Signaling]

 Press the Space Bar to toggle the Multi tone on/off.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle on/off.
 Enter Key:  Display Multi-Tone Select window.
 
#
#
#@
:chedit_mtonesel

                   [Multi Tone Select]


 If you know the CTCSS frequency or DCS code you want, you 
 can enter it directly with the 0 - 9 and [.] (period) keys.
 When the display shows the desired CTCSS frequency or DCS 
 code, press Enter to accept.
 If the frequency was invalid (not among the standard tones)
 the Tone/Code Select Window will appear as mentioned above.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle on/off.
 0 - 9, [.]: Direct tone frequency entry.
 Backspace:  Delete digit to left during direct entry.
 Enter Key:  Display Tone Select Window, and accept entry/
               selection.
 Esc Key:    Cancel input or selection.
 
#
#
#@
:chedit_cwanisel

                      [CW-ID or ANI/ENI select]


 Press the Space Bar to toggle the CW-ID or ANI/ENI.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle CW-ID, ANI/ENI and off.

#
#
#@
:chedit_actmode

                        [Action Mode]


 Press the Space Bar to toggle the Action Mode 
 Simplex/Duplex.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle Duplex/Simplex.

#
#
#@
:chedit_basetotuse

                       [TX Base T.O.T Use]

 Press the Space Bar to toggle the TX Base T.O.T use yes/no.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle yes/no.

#
#
#@
:chedit_basegtuse

                     [TX Base Guard Time Use]

 Press the Space Bar to toggle the TX Base Guard Time Use
 yes/no.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle yes/no.

#
#
#
:chedit_lout

    [Busy Channel/Tone Lock-Out: Carrier/Tone/Off Toggle]

 The Space Bar (or Backspace Key) toggles the BCLO/BTLO
 selection between Carrier Control (cw), CTCSS/DCS Control
 (tone), or off. If both the CTCSS and DCS Decoders were off,
 selecting "tone" here will turn CTCSS on, and the tone
 frequency will be displayed in the CTCSS Dec field.

 Note: You must press Enter after making a selection.

 Arrow Keys: Change field (after pressing Enter).
 Space Bar:  Toggle BCLO mode.
# Space Bar, Backspace: Toggle BCLO mode.
#
#
#
:chedit_txpwrsel

                     [Transmit Power Select]

 Selects TX power settings for this channel. 
 Choices are High and Low.

 Arrow Keys:          Change fields after selection.
 Space Bar/Backspace: Increment/Decrement Transmit Power
                      Level.

#
#
#
:chedit_totmute

                      [T.O.T Beep Mute]

 Press the Space Bar to toggle the T.O.T Beep Mute on/off.

 Arrow Keys:          Change fields after selection.
 Space Bar/Backspace: Toggle on/off.

#
#
#@
:chedit_rpttotuse

                   [TX Repeat T.O.T Use]

 Press the Space Bar to toggle the TX Repeat T.O.T Use
 yes/no.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle yes/no.

#
#
#@
:chedit_rpttotbp

                   [TX Repeat T.O.T Alert]

 Press the Space Bar to toggle the TX Repeat T.O.T Alert.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle on/off.

#
#
#@
:chedit_rpthtuse

                   [TX Repeat Hang Time Use]

 Press the Space Bar to toggle the TX Repat Hang Time Use
 yes/no..

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle yes/no.

#
#
#@
:chedit_rptgtuse

                   [TX Repeat Guard Time Use]

 Press the Space Bar to toggle the TX Repat Guard Time Use
 yes/no.

 Arrow Keys: Change fields after selection.
 Space Bar:  Toggle yes/no.

#
#
#
:file_select
                  [File Selection Window]

 Select a filename (lower-case letters) or subdirectory
 (upper-case, in angle brackets <>) using the Arrow Keys, and
 then the Enter Key to accept your selection. If you selected
 a subdirectory, the window contents will be replaced with
 that subdirectory's contents, from which you can select
 again. You can also delete a file or subdirectory with [F4].

 You can also enter a new drive letter or filespec directly.
 Pressing alphanumeric keys activates the filespec line
 editor along the bottom of the window. You can use wildcards
 ("*" or "?") to display only certain files (eg.,
 B:\CHDATA\*.CH and Enter displays only files with the "CH"
 extension in the CHDATA subdirectory on drive B). Tab
 returns you to the upper half of the selection window.
#
:page
#
 (at any time in Selection Window)
 Enter Key:  Accept selection.
 Esc Key:    Cancel operation and return to Channel Editor.
 Tab Key:    Switch between Selection Window and line editor.

 (for selection in upper part of window)
 Arrow Keys: Select filename/subdirectory.
 Home/End:   Jump to first/last selection on screen.
 [F4] Key:   Delete current file selection from disk.
 PageDown:   Jump down one page (for large directories).
 PageUp:     Jump up one page (for large directories).

 (for filespec editor at bottom of window)
 Delete:     Delete character under cursor.
 Backspace:  Delete character to left.
 Insert:     Toggle insert/overwrite modes.
#
#
#
:path_edit
                  [File Selection Window]

 Select a filename (lower-case letters) or subdirectory
 (upper-case, in angle brackets <>) using the Arrow Keys, and
 then the Enter Key to accept your selection. If you selected
 a subdirectory, the window contents will be replaced with
 that subdirectory's contents, from which you can select
 again.  If you select a file, you can delete it with [F4].

 You can also enter a new drive letter or filespec directly.
 Pressing alphanumeric keys activates the filespec line
 editor along the bottom of the window. You can use wildcards
 ("*" or "?") to display only certain files (eg.,
 B:\CHDATA\*.CH and Enter displays only files with the "CH"
 extension in the CHDATA subdirectory on drive B). Tab 
 returns you to the upper half of the selection window.
#
:page
#
 (at any time in Selection Window)
 Enter Key:  Accept selection.
 Esc Key:    Cancel operation and return to Channel Editor.
 Tab Key:    Switch between Selection Window and line editor.

 (for selection in upper part of window)
 Arrow Keys: Select filename/subdirectory.
 Home/End:   Jump to first/last selection on screen.
 [F4] Key:   Delete current file selection from disk.
 PageDown:   Jump down one page (for large directories).
 PageUp:     Jump up one page (for large directories).

 (for filespec editor at bottom of window)
 Delete:     Delete character under cursor.
 Backspace:  Delete character to left.
 Insert:     Toggle insert/overwrite modes.
#
#
#
:read_rom

     [Transfer data between PC and Transceiver's EEPROM]

 The Space Bar is used to proceed with the transfer operation
 after ensuring the hardware is set up for the transfer. To
 cancel and return to the Channel Editor, press the Esc Key
 instead.

 The status of the transfer operation will be displayed when
 finished (a few seconds after pressing the Space Bar).

 NOTE! Press the Esc Key if the system appears to hang. Then
 make sure the power indicator on the interface box is on,
 and check the cables for a connection problem.
#
#
#
:write_rom

    [Transfer data between PC and Transceiver's EEPROM]

 The Space Bar is used to proceed with the transfer operation
 after ensuring the hardware is set up for the transfer. To
 cancel and return to the Channel Editor, press the Esc Key
 instead.

 The status of the transfer operation will be displayed when
 finished (a few seconds after pressing the Space Bar).

 NOTE! Press the Esc Key if the system appears to hang. Then
 make sure the power indicator on the interface box is on,
 and check the cables for a connection problem.
#
#
#
:edit_common

               [Edit Common Data Parameters]

 CAUTION: Do not change Hardware Environment Parameters
 unless you are certain that the transceiver hardware is
 suitable for the new value.

 Editing these parameters requires that this program be
 started with the -p switch on the command line. Otherwise
 the settings can only be viewed.

 Use the Arrow Keys to select the parameter to edit. Then use
 the Space Bar or Backspace Key to toggle among all possible
 settings for that parameter. When all parameters are set as
 desired, press the Esc Key to return to the Channel Editor.
#
#
#
:edit_enviro

      [Hardware Environment Common Parameter Editing]

 CAUTION: Do not change Hardware Environment Parameters
 unless you are certain that the transceiver hardware is
 suitable for the new value.

 Editing these parameters requires that this program be
 started with the -f switch on the command line. Otherwise
 the settings can only be viewed.

 Use the Arrow Keys to select the parameter to edit. Then use
 the Space Bar or Backspace Key to toggle among all possible
 settings for that parameter.
 When all parameters are set as desired, press the Esc Key to
 return to the Common Data Editor.
#
#
#
:make_dir

          [Make a new subdirectory on current Path]

 Input the name of the new subdirectory (up to 8 characters),
 then press Enter. Press Esc or F8 to cancel if you change
 your mind.

 Backspace: Delete character to left of cursor
 Delete:    Delete character above cursor
 Insert:    Toggle Insert/Overwrite mode (Insert is default,
            Overwrite has block cursor)
#
#
#
:remove_dir
       [Remove the named (or pointed-to) subdirectory]

 Only empty child directories from the current subdirectory
 can be removed. In the file list, the inverse box can be
 positioned with the arrows to select a subdirectory to
 remove, by pressing F4. If the file list selection is not
 a subdirectory, a box will appear in which you can enter
 the name of the subdirectory to be removed. This name must
 be the same as one of the subdirectories displayed in the
 file list, and any files in that subdirectory must have
 already been deleted.

 Backspace: Delete character to left of cursor
 Delete:    Delete character above cursor
 Insert:    Toggle Insert/Overwrite mode (Insert is default,
               Overwrite has block cursor)
#
#

